GT750 Petcock: repair or replace?
Moderators: oldjapanesebikes, H2RICK, diamondj, Suzsmokeyallan
-
- Yeah Man, the Interstate
- Posts: 529
- Joined: Mon Oct 20, 2008 1:27 am
- Location: New Zealand
GT750 Petcock: repair or replace?
I've just started pulling bits off the GT to begin the big spruce up. However, I did go for a ride yesterday and was very impressed with the acceleration of the big girl - not as lumpy as they look
As I took the carbs off, it became very clear that the vacuum aspect of the petcock is not working. Petrol just kept coming out of all the lines. Is it possible to rectify this or do I need another petcock?
Thanks, Mike
As I took the carbs off, it became very clear that the vacuum aspect of the petcock is not working. Petrol just kept coming out of all the lines. Is it possible to rectify this or do I need another petcock?
Thanks, Mike
Burt Munro + John Britten + Kim Newcombe + Ivan Mauger = Kiwi Street Cred
72 GT750J
71 TS250R
71 H1A
72 GT750J
71 TS250R
71 H1A
- advant63
- To the on ramp
- Posts: 331
- Joined: Thu Oct 16, 2008 9:17 pm
- Country: canada
- Suzuki 2-Strokes: m12 or50 a100 s32-2 s32-2 t250 gt250 t500r
- Location: ontario
- Contact:
Re: GT750 Petcock: repair or replace?
the diaphragm is probably ok. just stuck, or fuel would be coming out the vacuum spigot as well. i vote for a rebuild. suzuki petcocks are a bit expensive and not correct (black). thailand petcocks are total garbage.
m12 or50 k10 a100
s32-2 s32-2 t250r
gt250 t500r gt550a
twin cobras in baskets
s32-2 s32-2 t250r
gt250 t500r gt550a
twin cobras in baskets
- oldjapanesebikes
- Moto GP
- Posts: 3229
- Joined: Sat Feb 07, 2009 12:43 am
- Country: Canada
- Suzuki 2-Strokes: GT750(Jx3,L,M,A,B),T500
- Location: Ontario
- Contact:
Re: GT750 Petcock: repair or replace?
For the GT750J/K the internals of the pet cock diaphragms are the same as those used on Kawasaki '69 through '72 H1's and those bits are still available from your Kwack dealer.
Ian
If at first you don't succeed, just get a bigger hammer !
If at first you don't succeed, just get a bigger hammer !
-
- Yeah Man, the Interstate
- Posts: 529
- Joined: Mon Oct 20, 2008 1:27 am
- Location: New Zealand
Re: GT750 Petcock: repair or replace?
Thanks for that. Think I'll pull her apart and see what looks not so flash. Will check against the parts diagram - I've learned that P.O.'s don't always put everything back
Burt Munro + John Britten + Kim Newcombe + Ivan Mauger = Kiwi Street Cred
72 GT750J
71 TS250R
71 H1A
72 GT750J
71 TS250R
71 H1A
- Coyote
- Moto GP
- Posts: 3404
- Joined: Tue Oct 21, 2008 2:41 pm
- Country: USA
- Suzuki 2-Strokes: GT550x2, GT750, GS1000
- Location: Tulsa, Oklahoma
Re: GT750 Petcock: repair or replace?
Probably all you need to replace is o-ring #26. Diaphragms tend to stick to adjacent parts but can be easily separated with a DULL razor blade.
I was born with nothing and still have most of it left.
.
1978 GS1000C
1976 GT550 ongoing money pit.
.
1978 GS1000C
1976 GT550 ongoing money pit.
- Rustygt550
- On the main road
- Posts: 172
- Joined: Mon Apr 06, 2009 6:56 am
- Location: Northern Ireland
Re: GT750 Petcock: repair or replace?
Thanks great info!! Do you have the part number for part #24
- oldjapanesebikes
- Moto GP
- Posts: 3229
- Joined: Sat Feb 07, 2009 12:43 am
- Country: Canada
- Suzuki 2-Strokes: GT750(Jx3,L,M,A,B),T500
- Location: Ontario
- Contact:
Re: GT750 Petcock: repair or replace?
Just take a look at the fiches here for part numbers. Availability will vary by country so you may have to do some searching to find a dealer than can supply what you need.
Ian
If at first you don't succeed, just get a bigger hammer !
If at first you don't succeed, just get a bigger hammer !
-
- To the on ramp
- Posts: 341
- Joined: Sat Oct 18, 2008 10:01 am
- Location: Hudson Valley, NY
Re: GT750 Petcock: repair or replace?
If the seat where the #26 o ring sits is corroded you can clean it with a q-tip and some polish so it doesn't have that infernal "slow drip".
So many Projects - So little time
- Coyote
- Moto GP
- Posts: 3404
- Joined: Tue Oct 21, 2008 2:41 pm
- Country: USA
- Suzuki 2-Strokes: GT550x2, GT750, GS1000
- Location: Tulsa, Oklahoma
Re: GT750 Petcock: repair or replace?
Depends on how deep the corrosion is. I cleaned up mine with a pencil eraser and some rouge. Lightly clamp the body in a vice with the seal surface facing up. Roughly shape rhe eraser to the taper. Apply some compound to the eraser and spin the pencil with your palms.
Mine does not leak which makes removing the tank a breeze.
Mine does not leak which makes removing the tank a breeze.
I was born with nothing and still have most of it left.
.
1978 GS1000C
1976 GT550 ongoing money pit.
.
1978 GS1000C
1976 GT550 ongoing money pit.
- tz375
- Moto GP
- Posts: 6206
- Joined: Mon Nov 03, 2008 10:47 am
- Location: Illinois
Re: GT750 Petcock: repair or replace?
Is that small O ring still available? I have two petcocks with small hard O rings that broke up when I tried to pry them off.
Mine is a 74
Mine is a 74
- oldjapanesebikes
- Moto GP
- Posts: 3229
- Joined: Sat Feb 07, 2009 12:43 am
- Country: Canada
- Suzuki 2-Strokes: GT750(Jx3,L,M,A,B),T500
- Location: Ontario
- Contact:
Re: GT750 Petcock: repair or replace?
I went into a seals and services outfit here in town that Uncle Rick suggested, and matched up some viton o-rings that seem to work fine. HVC offers the small o-ring also, but only as a part of a kit.tz375 wrote:Is that small O ring still available? I have two petcocks with small hard O rings that broke up when I tried to pry them off.
Ian
If at first you don't succeed, just get a bigger hammer !
If at first you don't succeed, just get a bigger hammer !
- H2RICK
- AMA Superbike
- Posts: 1659
- Joined: Sun Oct 19, 2008 11:07 am
- Country: CANADA
- Suzuki 2-Strokes: GT550A, GSF1200SK6 currently
- Location: Cowtown aka Calgary, Canada
Re: GT750 Petcock: repair or replace?
Another good refurbishing device for the pintle seat is an unused chopstick from your favourite Oriental takeout place. A little work with a sharp knife so the chopstick end matches the taper of the pintle seat
and you can whirl it back and forth between your palms to polish the seat just like lapping a valve with a valve seating stick.
If the seat has visible corrosion pockets in it, you might want to try the same trick with a little extra fine valve lapping compound on the chopstick......but don't overdo it. Five or six rotations of the chopstick and then wipe the seat clean and check it. Repeat as necessary.
and you can whirl it back and forth between your palms to polish the seat just like lapping a valve with a valve seating stick.
If the seat has visible corrosion pockets in it, you might want to try the same trick with a little extra fine valve lapping compound on the chopstick......but don't overdo it. Five or six rotations of the chopstick and then wipe the seat clean and check it. Repeat as necessary.
GT550A Mint & Original
H2A Semi-Hot Rod Built From A Basket Case
KZ650C2 Mint & Original...mostly
GSF1200SK6 Bandit...My LD Ride
Additional H2 projects In Boxes.....
MBD Sufferer
H2A Semi-Hot Rod Built From A Basket Case
KZ650C2 Mint & Original...mostly
GSF1200SK6 Bandit...My LD Ride
Additional H2 projects In Boxes.....
MBD Sufferer
- tz375
- Moto GP
- Posts: 6206
- Joined: Mon Nov 03, 2008 10:47 am
- Location: Illinois
Re: GT750 Petcock: repair or replace?
oldjapanesebikes wrote:I went into a seals and services outfit here in town that Uncle Rick suggested, and matched up some viton o-rings that seem to work fine. HVC offers the small o-ring also, but only as a part of a kit.tz375 wrote:Is that small O ring still available? I have two petcocks with small hard O rings that broke up when I tried to pry them off.
I have an HVC set and that O ring is a couple of sizes too large for4 some reason. I'll try the local auto store in the morning
- Jughead
- This IS the real me!!!
- Posts: 540
- Joined: Tue Dec 02, 2008 7:48 pm
Re: GT750 Petcock: repair or replace?
If you can't find one of the regular Black O-rings that you need see if they sell Green Air Conditioning Orings.They come in Strange Sizes and are Gas resistant.
Hang me from the Tree of Shame.Damn! I forgot the Rope.
- Suzsmokeyallan
- Moto GP
- Posts: 4326
- Joined: Fri Oct 24, 2008 9:11 am
- Location: Mostly Barbados, sometimes Florida and western Canada
- Contact:
Re: GT750 Petcock: repair or replace?
Jug you wont find an A/C line o-ring in that size, not even a high side o-ring is that small. You would have to size it at an o-ring store or get an HVC kit.
Two strokes, its just that simple.
69 Suz U70
69 Suz T500
72 Suz GT750 cafe
74 Suz TS250
74 Suz GTXVR project
75 Suz RE5
75 Suz GT750
76 Suz TS400
76 Suz GT750
81 Suz GSX1100
86 Suz RG500x2
88 Hon CR500
93 Hon CBR900RR
98 Suz GSF1200x3
15 Kaw Ninja H2
69 Suz U70
69 Suz T500
72 Suz GT750 cafe
74 Suz TS250
74 Suz GTXVR project
75 Suz RE5
75 Suz GT750
76 Suz TS400
76 Suz GT750
81 Suz GSX1100
86 Suz RG500x2
88 Hon CR500
93 Hon CBR900RR
98 Suz GSF1200x3
15 Kaw Ninja H2