Archived Posts
Moderators: oldjapanesebikes, H2RICK, diamondj, Suzsmokeyallan
-
- Supreme UFOB
- Posts: 34711
- Joined: Wed Dec 31, 1969 6:00 pm
Or Even Have an IQ Higher than Forrest Gump.vince69007 wrote:thats one of the problems with e-bay. you dont need to be a mechanic (or even mechanically inclined) to destroy a motorcycle and list all the parts.,
I bought a Set of Spare Cylinders a Few weeks ago that supposedly had been in Great Usable Condition.When I got them they Had Pried on the Gasket Surface on the Bottom of the Cylider and Beat the top of the Liner With a Hammer.Yeah Sure they're in Useable Condition but I'm going to have to have the Surfaces on one Cylinder Milled.
-
- Supreme UFOB
- Posts: 34711
- Joined: Wed Dec 31, 1969 6:00 pm
-
- Supreme UFOB
- Posts: 34711
- Joined: Wed Dec 31, 1969 6:00 pm
This is just down the road from me
If anyone is interested, I could take a look or pick it up, since this is just a few miles from where I work.
Kevin
Kevin
-
- Supreme UFOB
- Posts: 34711
- Joined: Wed Dec 31, 1969 6:00 pm
Then again, sometimes the stupid people who part out things on ebay that they have no concept of are nice to work with. I got a locked up GT550 engine in the frame, minus the carbs, for $26 dollars. Spent $75 dollars gas to go get it. So far the only thing not usable was the crank, due to corrosion. That let me put my bike back on the road for a little more that what one cylinder should have cost, and I have a bunch of parts left over.
Kevin
Kevin
-
- Supreme UFOB
- Posts: 34711
- Joined: Wed Dec 31, 1969 6:00 pm
exception to Murphys law.. LoL. i have only seen ONE T500 and 0 parts up here, and One 380. seems like all the other countries got all the bikes and parts..jkevinlilly wrote:Then again, sometimes the stupid people who part out things on ebay that they have no concept of are nice to work with. I got a locked up GT550 engine in the frame, minus the carbs, for $26 dollars. Spent $75 dollars gas to go get it. So far the only thing not usable was the crank, due to corrosion. That let me put my bike back on the road for a little more that what one cylinder should have cost, and I have a bunch of parts left over.
Kevin


-
- Supreme UFOB
- Posts: 34711
- Joined: Wed Dec 31, 1969 6:00 pm
-
- Supreme UFOB
- Posts: 34711
- Joined: Wed Dec 31, 1969 6:00 pm
That's only 30 minutes south of ME!!!!!!!!!!!!!!!!!!!
I am definitely going to bid on it!! Especially since my 380's down for a while. I don't have the money for it, but I will sell something to get it if I have to.
Would it be possible for anyone else in the area to keep from upping the bid. I'm a last minute bidder, I always try and sneak it in there as low as possible.
Suzsmokeyallan - Thank you SO MUCH for pointing that out!!!
I am definitely going to bid on it!! Especially since my 380's down for a while. I don't have the money for it, but I will sell something to get it if I have to.
Would it be possible for anyone else in the area to keep from upping the bid. I'm a last minute bidder, I always try and sneak it in there as low as possible.
Suzsmokeyallan - Thank you SO MUCH for pointing that out!!!
-
- Supreme UFOB
- Posts: 34711
- Joined: Wed Dec 31, 1969 6:00 pm
Cooteboy theres a rule on this board that once you are seriously going to bid on an e-bay item its 'hands off' from everyone else on here, so bid with confidence.
I hope you get it, as i have a 74 Buffalo i'm converting to the
"project bike", so if theres some parts i can help you with particular to the 74 model i wont need, they are yours.
I hope you get it, as i have a 74 Buffalo i'm converting to the
"project bike", so if theres some parts i can help you with particular to the 74 model i wont need, they are yours.