Suzuki2Strokes.com

Sundial Moto Sports

Suzuki Two-Stroke Message Board
Suzuki2Strokes.com
It is currently Thu Jan 23, 2020 8:22 am

All times are UTC - 6 hours




Post new topic Reply to topic  [ 3 posts ] 
Author Message
PostPosted: Mon Jun 03, 2019 8:47 am 
Offline
Moto GP
User avatar

Joined: Mon Dec 13, 2010 4:32 pm
Posts: 3489
Location: southwestern Pennsylvania
Country: USA
Bikes owned: 69 T350 thru 75 GT750
Just about have the GT550 motor rebuilt.
Have an extra part that looks pretty much exactly the same as the kickstart shaft plug, part # 09242-23001.
https://i.ebayimg.com/images/g/6gUAAOSw ... -l1600.jpg

This plug is oily & clean. I can’t find any place that it might have been. I hoping its an extra part that was included with some used parts I bought.

No indication of where it might have been per any of the documents I reviewed. Given the occasional errors in the documents, I figure its better to be safe than sorry.
Any ideas or answers?

_________________
BAS (Bike Acquisition Syndrome) - too many bikes but have room for more

Suzuki:
GT750 2x75
GT550 72 project & 75
GT380 72
T500 73 project
T350 69, 71 & 72 project
T250 72
Honda 85 CB650SC & 86 CB700SC
09 Triumph Bonneville SE


Top
 Profile  
 
PostPosted: Tue Jun 04, 2019 1:16 pm 
Offline
Expert racer

Joined: Wed Jul 10, 2013 12:04 pm
Posts: 1035
Country: England, UK
Bikes owned: FZ50, GP100, RG125 Gamma, GT380, Bandit 1200S
So far as i can tell it is, as you say, the blanking plug that fits at the end of the kickstarter shaft. Part 18 in the following pic. So long as you already have a plug there, then maybe it is a spare part.
Image


Top
 Profile  
 
PostPosted: Tue Jun 04, 2019 7:05 pm 
Offline
Moto GP
User avatar

Joined: Mon Dec 13, 2010 4:32 pm
Posts: 3489
Location: southwestern Pennsylvania
Country: USA
Bikes owned: 69 T350 thru 75 GT750
Thanks.

I have not yet put the kickstart shaft plug in. Its a lot easier to assemble the crankcase halves with the plug out. I used a small nylon spring clip in that opening to hold the kickstart shaft in place when assembling the halves.

There is a small notch is the spacer, part 13, that faces the plug. I figure the Suzuki factory had a tool that fit in the opening & held the shaft in place during assembly, and that it used the notch to properly orient the spacer with respect the the pin, part 15.

_________________
BAS (Bike Acquisition Syndrome) - too many bikes but have room for more

Suzuki:
GT750 2x75
GT550 72 project & 75
GT380 72
T500 73 project
T350 69, 71 & 72 project
T250 72
Honda 85 CB650SC & 86 CB700SC
09 Triumph Bonneville SE


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 3 posts ] 

All times are UTC - 6 hours


Who is online

Users browsing this forum: No registered users and 61 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group
Sundial Moto Sports forum © by Eric F. Kalamaja
Suzuki2Strokes.com