Archived Posts
Moderators: oldjapanesebikes, H2RICK, diamondj, Suzsmokeyallan
-
- Supreme UFOB
- Posts: 34711
- Joined: Wed Dec 31, 1969 6:00 pm
The RZ is probably the most fun bike to ride that I have. It is blistering fast for a 350 and has a power band like a moto cross bike. It will fly even with my fat arse on it.
I still like the Buffalo best because it is not so nervous. I still don't have the carbs completly sorted and I have a minor (I hope) clutch problem.
The LC needs some work, and parts are almost non-existant in the US. I still need a headlight bulb and trim ring and the turn signals. It runs OK, but the carbs need some tweeking. There is a pretty good LC following in the UK, but parts are almost as expensive as H2 stuff when you add in the shipping from the UK.
I picked up the XS650 from my neighbor who bought it new. It only has 5700 miles on it. I rebuilt the carbs, changed the oil, added a battery, and it started right up. The only cosmetic issue is the tank has some scratches on it so it needs repainting, but the inside is clean as a new one. I think a friend of mine who has not ridden in a long time is going to end up with it.
The H2 will be rebuilt in '08, but just as a rider. It came with a set of near new chrome TNT chambers when I bought it. I don't have the skill, knowledge, patience, money or desire to do an original restoration. Been there, done that with a '69 Camaro and all you end up with is a trailer queen that you can't ride for fear of getting a rock chip.
Wayne
I still like the Buffalo best because it is not so nervous. I still don't have the carbs completly sorted and I have a minor (I hope) clutch problem.
The LC needs some work, and parts are almost non-existant in the US. I still need a headlight bulb and trim ring and the turn signals. It runs OK, but the carbs need some tweeking. There is a pretty good LC following in the UK, but parts are almost as expensive as H2 stuff when you add in the shipping from the UK.
I picked up the XS650 from my neighbor who bought it new. It only has 5700 miles on it. I rebuilt the carbs, changed the oil, added a battery, and it started right up. The only cosmetic issue is the tank has some scratches on it so it needs repainting, but the inside is clean as a new one. I think a friend of mine who has not ridden in a long time is going to end up with it.
The H2 will be rebuilt in '08, but just as a rider. It came with a set of near new chrome TNT chambers when I bought it. I don't have the skill, knowledge, patience, money or desire to do an original restoration. Been there, done that with a '69 Camaro and all you end up with is a trailer queen that you can't ride for fear of getting a rock chip.
Wayne
-
- Supreme UFOB
- Posts: 34711
- Joined: Wed Dec 31, 1969 6:00 pm
Doffin, that pipe is a TCE 3into1 and it is not very loud at all. It gives the bike a lot of torque in the low to mid range, but it signs off at about 6000, so it does not make power up high. Fortunately, it makes the power where I ride most of the time, saves about 40 lbs, and it looks so KOOL.
Wayne
Wayne
-
- Supreme UFOB
- Posts: 34711
- Joined: Wed Dec 31, 1969 6:00 pm
-
- Supreme UFOB
- Posts: 34711
- Joined: Wed Dec 31, 1969 6:00 pm
The Story Of My GT550A.....
Here it is for those who have a high boredom threshold.....
http://s73.photobucket.com/albums/i234/ ... 0%20Stuff/
http://s73.photobucket.com/albums/i234/ ... 0%20Stuff/
-
- Supreme UFOB
- Posts: 34711
- Joined: Wed Dec 31, 1969 6:00 pm
First Bike GT750 L
After 20 years, I pulled my GT750 out of the basement where it had been stored. I cleaned it up a bit and decided to fulfill a dream I had when I was 25, to build a GT750 drag bike. I thought I would document the progress since it seems to be a relatively less traveled path I'm going down...
These pics are from the early stages...but include most of the internal engine work, carb work, swingarm and rear tire conversion as well as the frame strip down to lighten the load somewhat. Several of you have helped me get this project moving and I appreciate the support.
These pics are from the early stages...but include most of the internal engine work, carb work, swingarm and rear tire conversion as well as the frame strip down to lighten the load somewhat. Several of you have helped me get this project moving and I appreciate the support.
Last edited by Admin on Tue Jun 03, 2008 12:29 pm, edited 1 time in total.
-
- Supreme UFOB
- Posts: 34711
- Joined: Wed Dec 31, 1969 6:00 pm
GT Startup
This was the day I started the engine and added one more buffalo to the herd...