Dear All
I have just had my carbs cleaned and rebuilt after leaving the bike standing for almost two years and a build up of salt formng in many places.
Many of you advised me that the problems i had - which was that the bike wouldnt run when the choke was switched off - were down to blocked pilot jets.
THe problem is that the heads are damaged and the carb specialist here didn't think it was wise to drill them out. He was convinced that if he cleaned everything else, including the pilot jets from the other side, all would be fine.]
Putting them back, now the bike runs with choke off BUT when you open the throttle, it makes that unique noise like fuel starvation and takes a while for revs to pick up. Also, you cannot pull away with the choke off.
Could it be one of the following
THe mixture is too LEAN on all three and those external adjuster air flow screws need to be closed?
Or is it possible that my ignition timing is out? (Would that also give such symptoms?)
ALSO, is there any product i can throw into the gas tank which would clear through any blockages in the carbs?
thanks for your help and patience
MJ in Beirut
carb conundrem
Moderators: oldjapanesebikes, H2RICK, diamondj, Suzsmokeyallan
-
- To the on ramp
- Posts: 254
- Joined: Tue Apr 30, 2013 9:28 am
- Country: Lebanon
- Suzuki 2-Strokes: gsx 750R, GPZ 750, GT380
- Location: Lebanon
-
- AMA Superbike
- Posts: 1769
- Joined: Tue Oct 14, 2008 6:47 pm
- Location: Blythewood, SC, USA
Re: carb conundrem
I have used a reverse drill bit to remove pilots before, but it's not easy. They are so soft. That said, I doubt you can get the carb very clean without getting the jets out.
Lane
Lane
If you stroke it more than twice; you're playing with it.
Too many bikes, too much time, ENOUGH SPACE, FINALLY! Never enough money.........
Too many bikes, too much time, ENOUGH SPACE, FINALLY! Never enough money.........
- jabcb
- Moto GP
- Posts: 4241
- Joined: Mon Dec 13, 2010 4:32 pm
- Country: USA
- Suzuki 2-Strokes: 69 T350 thru 75 GT750
- Location: southwestern Pennsylvania
Re: carb conundrem
Had a stuck pilot jet on a T350 where some PO buggered up the screw driver slot.
Used the smallest drill/extractor set & the pilot jet came out surprisingly easy.
The smallest set was a 5/64 inch drill bit + #1 screw extractor.
I suspect that turning the extractor slowly by hand with a crescent wrench was key to making it easy for an amateur mechanic.
Used the smallest drill/extractor set & the pilot jet came out surprisingly easy.
The smallest set was a 5/64 inch drill bit + #1 screw extractor.
I suspect that turning the extractor slowly by hand with a crescent wrench was key to making it easy for an amateur mechanic.
BAS (Bike Acquisition Syndrome) - too many bikes but have room for more
Suzuki:
GT750 2x75
GT550 72 & 75
GT380 72
T500 69 project & 73 project
T350 69 & 71
Honda 85 CB650SC & 86 CB700SC
09 Triumph Bonneville SE
Suzuki:
GT750 2x75
GT550 72 & 75
GT380 72
T500 69 project & 73 project
T350 69 & 71
Honda 85 CB650SC & 86 CB700SC
09 Triumph Bonneville SE
-
- Yeah Man, the Interstate
- Posts: 590
- Joined: Tue Mar 10, 2015 12:35 pm
- Country: WALES
- Suzuki 2-Strokes: suzuki gt 550j
- Location: Wales
Re: carb conundrem
Hi MJ . First thing is there is nothing you can put in the gas tank that will clean your carbs efficiently. I think you are right that your bike is running lean off choke and that will be because your pilot jets can only be cleaned properly by removing them. Not only does the jet have a hole in the end metering gas there are holes in the sides that cause the gas to froth to help conbine it with the air. Its also important to get the jet out because it fits into a passage which is hard to clear normally but with the jet in impossible.
98 carb Blackbird and GT550j