Cracked T500 Head
Moderators: oldjapanesebikes, H2RICK, diamondj, Suzsmokeyallan
-
- On the main road
- Posts: 165
- Joined: Sun Aug 23, 2009 11:46 am
- Country: USA (former Canuck)
- Suzuki 2-Strokes: T500, GT550 (electric conversion), Hayabusa
- Location: Maine/Nova Scotia
Cracked T500 Head
I did this at Loring this past weekend at a land-speed event. It was shaved .040" (1 mm.) Comments, thoughts, etc. appreciated! I've heard that these heads have a propensity for cracking but this took me by surprise. It's not like I was running nitromethane or anything, lol. How can I prevent this from happening in the future?
thanks,
Frank
thanks,
Frank
- tz375
- Moto GP
- Posts: 6204
- Joined: Mon Nov 03, 2008 10:47 am
- Location: Illinois
Re: Cracked T500 Head
Frank, That's two different cracks intersecting.
PEDRO or Zookie are the resident 500 guys but I think I'd would be looking at repop air cooled TR heads for that bike.
PEDRO or Zookie are the resident 500 guys but I think I'd would be looking at repop air cooled TR heads for that bike.
-
- Road race school
- Posts: 785
- Joined: Tue Oct 14, 2008 11:00 pm
- Location: Wharton, NJ USA
Re: Cracked T500 Head
Years ago there was a guy on this board that went by the username "Krash". Krash raced T500's and had a continuous issue with cracking the left cylinder head on his race bike. I think he finally figured out that he was milling the heads too much and that there was an inherent weakness in the cylinder head casting as the cracks were always in the same spot and the same head. Don't know if this applies to your situation but I would look into getting a set of TR500 replica heads from Pedro. They will cost you a bit initially but being able to stop worrying about cracking the stock heads should make it worthwhile.
Jim
Jim
-
- On the main road
- Posts: 165
- Joined: Sun Aug 23, 2009 11:46 am
- Country: USA (former Canuck)
- Suzuki 2-Strokes: T500, GT550 (electric conversion), Hayabusa
- Location: Maine/Nova Scotia
Re: Cracked T500 Head
This was the left head! I didn't know Pedro was making heads, I'll contact him.
Thanks guys. I remember Krash's race stories. I wonder if some of them are still on Eric's site? Have to look...
Thanks guys. I remember Krash's race stories. I wonder if some of them are still on Eric's site? Have to look...
- Suzukidave
- Moto GP
- Posts: 3980
- Joined: Fri Oct 24, 2008 5:55 pm
- Country: US
- Suzuki 2-Strokes: GT750 x2 97 -1200 Bandit 86 GSXR1100
- Location: Lancaster Pa.
Re: Cracked T500 Head
The picture has me puzzled a bit .. the stud hole in the upper right is not where the stud hole in the head is .. how did the hole get so much larger than the rest and not where it should be if the head bolt went thru that hole ?
the older i get the faster i was
-
- Expert racer
- Posts: 1306
- Joined: Wed Oct 13, 2010 2:55 pm
- Country: England
- Suzuki 2-Strokes: TS100, T200, GT250, T500, GT500, GT550, GT750, GS750
- Location: Southeast England
- Contact:
Re: Cracked T500 Head
There are 2 different sized studs that retain a 500 head Dave....4 short 8mm bolts, alternated with 4 long crankcase studs. The gasket has been mis-shapen by the cylinder blowing.
I have cracked a few heads in the dim and distant past.........
I'm guessing now, but is the crack between the 2 long studs that are farthest apart? That's where mine always cracked.....and I think it was my reluctance to torque the head down tight enough on the 8mm short bolt between these 2 long studs. As we all know, these short bolts screw into the aluminium of the barrell/jug body, they weaken, wear out, and eventually strip. With a stock motor, I found I could leave out all the 8mm bolts except that corner one where the gap between the long studs is larger, and suffer no problems at all. Ultimately, I inserted a stud into that thread, and secured it with a nut, as I have done in the exhaust ports. I run a slightly ported motor now, with Barton squish heads, and have never suffered any cracks since.
I have cracked a few heads in the dim and distant past.........
I'm guessing now, but is the crack between the 2 long studs that are farthest apart? That's where mine always cracked.....and I think it was my reluctance to torque the head down tight enough on the 8mm short bolt between these 2 long studs. As we all know, these short bolts screw into the aluminium of the barrell/jug body, they weaken, wear out, and eventually strip. With a stock motor, I found I could leave out all the 8mm bolts except that corner one where the gap between the long studs is larger, and suffer no problems at all. Ultimately, I inserted a stud into that thread, and secured it with a nut, as I have done in the exhaust ports. I run a slightly ported motor now, with Barton squish heads, and have never suffered any cracks since.
Keeping old 2 strokes alive !
- Suzukidave
- Moto GP
- Posts: 3980
- Joined: Fri Oct 24, 2008 5:55 pm
- Country: US
- Suzuki 2-Strokes: GT750 x2 97 -1200 Bandit 86 GSXR1100
- Location: Lancaster Pa.
Re: Cracked T500 Head
Ah yes .. i should have looked before i asked http://www.ozebook.com/compendium/t500_ ... pascal.htm" onclick="window.open(this.href);return false;titan performance wrote:There are 2 different sized studs that retain a 500 head Dave....4 short 8mm bolts, alternated with 4 long crankcase studs.
the older i get the faster i was
-
- On the main road
- Posts: 165
- Joined: Sun Aug 23, 2009 11:46 am
- Country: USA (former Canuck)
- Suzuki 2-Strokes: T500, GT550 (electric conversion), Hayabusa
- Location: Maine/Nova Scotia
Re: Cracked T500 Head
titan performance wrote:I'm guessing now, but is the crack between the 2 long studs that are farthest apart? .... I run a slightly ported motor now, with Barton squish heads, and have never suffered any cracks since.
I'm not sure what you mean by between the 2 long studs. The crack is perpendicular to a line drawn between those studs but doesn't run stud-to-stud (here's another pic that might show it better.) The crack also extends around the edge of the head.
I'd love to get some squish heads. Eric apparently lost his source. What's the deal with Barton heads? Maybe it's not necessary as I'm running stock pipes in my class. Thanks for any info on this.
Frank
- Zook-e
- Smokin'
- Posts: 617
- Joined: Mon Oct 13, 2008 7:29 pm
- Location: Southwestern Virginia
- Contact:
Re: Cracked T500 Head
My squish head source was from Crooks and that for their personal reasons dried up. Pedro can probably source some.
As for the milled heads, that has only happened to me once and I have used 40 and 60 thou heads. It is very important to heat cycle, completely cool down and retorque the heads at least three times. Each time I have heat cycled the motor the torque specs have changed and needed retorquing. Make sure the cylinder surface is also surfaced and I have used 600 grit sandpaper on a glass surface with wd-40 to do this. Any imperfections can cause a leak. I also coppercoat my copper gaskets.
Some builders use only the 4 large bolts, but I use all 8. Make sure the small bolt hole threads are chased and clean. Helicoil or threadsert them if they are vague at all. And make sure all threads on bolts and studs are cleaned.
Some heads have imperfections in castings that also may cause cracking.
As for the milled heads, that has only happened to me once and I have used 40 and 60 thou heads. It is very important to heat cycle, completely cool down and retorque the heads at least three times. Each time I have heat cycled the motor the torque specs have changed and needed retorquing. Make sure the cylinder surface is also surfaced and I have used 600 grit sandpaper on a glass surface with wd-40 to do this. Any imperfections can cause a leak. I also coppercoat my copper gaskets.
Some builders use only the 4 large bolts, but I use all 8. Make sure the small bolt hole threads are chased and clean. Helicoil or threadsert them if they are vague at all. And make sure all threads on bolts and studs are cleaned.
Some heads have imperfections in castings that also may cause cracking.
"If you keep hitting your head against the wall you will eventually put a hole in the wall or your head"
1968 T500 Monoshock, 1972 GT750 Custom, 1973 GT750 Lemans
http://www.sundialmotosports.com
1968 T500 Monoshock, 1972 GT750 Custom, 1973 GT750 Lemans
http://www.sundialmotosports.com
-
- On the main road
- Posts: 165
- Joined: Sun Aug 23, 2009 11:46 am
- Country: USA (former Canuck)
- Suzuki 2-Strokes: T500, GT550 (electric conversion), Hayabusa
- Location: Maine/Nova Scotia
Re: Cracked T500 Head
Thanks Eric. I retorqued twice (I think) and will pay better attention to that - what thickness head gasket do you recommend? I used a Cometic .010" (might have been .012) with coppercoat. I've been thinking of leaving the next set of heads at stock thickness and maybe decking the cylinders to get a bit more compression.
This engine had 145# cold cranking pressure. Does this seen "in the ballpark" to you?
Frank
This engine had 145# cold cranking pressure. Does this seen "in the ballpark" to you?
Frank
- jabcb
- Moto GP
- Posts: 4241
- Joined: Mon Dec 13, 2010 4:32 pm
- Country: USA
- Suzuki 2-Strokes: 69 T350 thru 75 GT750
- Location: southwestern Pennsylvania
Re: Cracked T500 Head
This might help. A NOS T500 left cylinder head is on eBay for $75.
http://cgi.ebay.com/ebaymotors/ws/eBayI ... AUS%3A1123
http://cgi.ebay.com/ebaymotors/ws/eBayI ... AUS%3A1123
BAS (Bike Acquisition Syndrome) - too many bikes but have room for more
Suzuki:
GT750 2x75
GT550 72 & 75
GT380 72
T500 69 project & 73 project
T350 69 & 71
Honda 85 CB650SC & 86 CB700SC
09 Triumph Bonneville SE
Suzuki:
GT750 2x75
GT550 72 & 75
GT380 72
T500 69 project & 73 project
T350 69 & 71
Honda 85 CB650SC & 86 CB700SC
09 Triumph Bonneville SE
-
- Yeah Man, the Interstate
- Posts: 554
- Joined: Wed Apr 01, 2009 11:47 pm
- Location: NM USA
- Contact:
Re: Cracked T500 Head
On the Kawi H2 heads, under very hard racing use, the outer heads will crack. The solution was to add couple of weld beads along the bottom of the fin, on the side. I also always chamfer all the edges and holes to stop any stressers.
Visiting from the "K" camp...........
-
- Around the block
- Posts: 59
- Joined: Mon Mar 10, 2014 12:52 pm
- Country: USA
- Suzuki 2-Strokes: 75 Suzuki T500M Titan
Re: Cracked T500 Head
Can anyone out there let me know how to go about doing copper head gaskets?? I'm having Eric port the cylinders on my 75 Titan, and he suggested using a copper head gasket to raise the compression slightly.
Doe this mean just using the liquid copper make-a-gasket stuff ... or is there actually a stiff metal copper gasket you can buy somewhere?
Any help appreciated - thanks in advance.
Sterling
Doe this mean just using the liquid copper make-a-gasket stuff ... or is there actually a stiff metal copper gasket you can buy somewhere?
Any help appreciated - thanks in advance.
Sterling
-
- On the main road
- Posts: 165
- Joined: Sun Aug 23, 2009 11:46 am
- Country: USA (former Canuck)
- Suzuki 2-Strokes: T500, GT550 (electric conversion), Hayabusa
- Location: Maine/Nova Scotia
Re: Cracked T500 Head
Cometic sells 'em but this is what I used when my head cracked. I've run several land-speed events since I replaced with stock aluminum w/o any problems.
-
- Around the block
- Posts: 59
- Joined: Mon Mar 10, 2014 12:52 pm
- Country: USA
- Suzuki 2-Strokes: 75 Suzuki T500M Titan
Re: Cracked T500 Head
Ah, I see. Well of course, I already have a new set of oem head gaskets and base gaskets ready to go. But once Eric mentioned doing the thinner copper gasket, I was on a mission. Obviously, it would be much easier to use the gaskets I have, rather than sourcing some copper ones.Frank wrote:Cometic sells 'em but this is what I used when my head cracked. I've run several land-speed events since I replaced with stock aluminum w/o any problems.
Also, this is only going to be a street bike, I'm not racing it or anything. I just wondered if having ported heads, chambers, and rejetting required the use of a thinner head gasket, or if I can just use the regular ones ...
I feel so lost sometimes, lol.
thanks -