Page 2 of 2
Re: Yamazuki
Posted: Fri Apr 22, 2016 11:01 am
by jabcb
Looking good.
What did you paint the engine with?
Re: Yamazuki
Posted: Mon May 23, 2016 11:54 am
by Rassie
Dupli Color Engine enamel with ceramic from Autozone. Cleaning the engine is of utmost importance when doing this. It has to be completely clean and I used Kerosene first with a very strong grease remover/engine cleaner afterwards and cleaned it up with a stainless steel brush. Then lightly sand with 600 paper as much as you can. Wipe it down with lacquer thinners before you paint it.
Re: Yamazuki
Posted: Mon May 23, 2016 11:58 am
by Rassie
Re: Yamazuki
Posted: Mon May 23, 2016 12:36 pm
by Suzukidave
Wow !! that came out so nice
Re: Yamazuki
Posted: Mon May 23, 2016 2:53 pm
by Rassie
Dave you should take some credit since I did end up doing the same with the side engine mounts, essentially copied what you did with your project.
Re: Yamazuki
Posted: Mon May 23, 2016 8:36 pm
by Suzukidave
Thanx , but the engine mount was such a small part to the creative work you did on this build .. 2 thumbs up
Re: Yamazuki
Posted: Tue Jul 05, 2016 5:14 am
by Suzukidave
Have you been out to any events to show the new build
Re: Yamazuki
Posted: Thu Sep 01, 2016 8:40 pm
by Warehouse1001
Rassie wrote:Dupli Color Engine enamel with ceramic from Autozone. Cleaning the engine is of utmost importance when doing this. It has to be completely clean and I used Kerosene first with a very strong grease remover/engine cleaner afterwards and cleaned it up with a stainless steel brush. Then lightly sand with 600 paper as much as you can. Wipe it down with lacquer thinners before you paint it.
Did you have any problems with the paint chipping or coming off while tightening down the crankcase bolts?
Re: Yamazuki
Posted: Fri Sep 02, 2016 9:40 am
by rngdng
HOLY CRAP!!!! That turned out awesome. You may have the first Buffalo that I think looks better than mine! Most impressive.
Lane
Re: Yamazuki
Posted: Fri Sep 02, 2016 9:46 am
by desmocat
Bravo, well done sir. Definitely an impressive build!
Re: Yamazuki
Posted: Sun Sep 04, 2016 3:10 am
by wolfgangh
Hello Rassi,
this is an awesome bike built to very high standard.
I am currently building a BIMOTA HB1 replica with GT750 engine, also using JEMCO pipes. Have you done the stinger / silencer modification due to noise reduction or for design reasons? I have never heard my JEMCOS operating but I fear they might be too loud for European roads.
Any inputs about that?
Do you have noise limitations in your country and how did you pass?
best regards
Wolfgang
Re: Yamazuki
Posted: Mon Nov 14, 2016 9:04 am
by Rassie
Suzukidave wrote:Have you been out to any events to show the new build
Dave,
Yes. I have been riding it around quite a bit and even got pulled over by the cops a week or so ago. It causes quite a stir wherever I go, most people have no idea what it is. Some figure it out quite quickly. The hipster crowd ignore it completely
Re: Yamazuki
Posted: Mon Nov 14, 2016 9:06 am
by Rassie
Warehouse1001 wrote:Rassie wrote:Dupli Color Engine enamel with ceramic from Autozone. Cleaning the engine is of utmost importance when doing this. It has to be completely clean and I used Kerosene first with a very strong grease remover/engine cleaner afterwards and cleaned it up with a stainless steel brush. Then lightly sand with 600 paper as much as you can. Wipe it down with lacquer thinners before you paint it.
Did you have any problems with the paint chipping or coming off while tightening down the crankcase bolts?
Sorry for the tardy reply, I was on a 2 month trip across the country visiting National Parks. No I had no issues with paint chipping when installing the motor. I did have some after the fact but just touched it up with a brush.
Re: Yamazuki
Posted: Mon Nov 14, 2016 9:10 am
by Rassie
wolfgangh wrote:Hello Rassi,
this is an awesome bike built to very high standard.
I am currently building a BIMOTA HB1 replica with GT750 engine, also using JEMCO pipes. Have you done the stinger / silencer modification due to noise reduction or for design reasons? I have never heard my JEMCOS operating but I fear they might be too loud for European roads.
Any inputs about that?
Do you have noise limitations in your country and how did you pass?
best regards
Wolfgang
Wolfgang,
The pipes are very loud. We do not have very strict control over emissions and noise over here in North Carolina where I live so I can get away with it. However I know how strict it is in Germany and these pipes will definitely be too loud. Your best bet would be to see if you can restrict the baffles more on the standard Jemcos.
Re: Yamazuki
Posted: Mon Nov 14, 2016 7:10 pm
by johnu
Sweet build, love it!