Part supplier

Photos and progress of your restorations, even bikes you had but no longer own.

Moderators: oldjapanesebikes, H2RICK, Suzsmokeyallan

Post Reply
Frogy
Still in the Driveway
Posts: 6
Joined: Mon Apr 02, 2018 3:16 am
Country: England
Suzuki 2-Strokes: Suzuki GT550 1976

Part supplier

Post by Frogy »

Hi just started a Restoration project on a Suzuki 1976 GT550 can anyone advise where is the best place to source replacement parts etc for this bike i am based in Chesterfield England

regards
GTandcbr
Yeah Man, the Interstate
Posts: 590
Joined: Tue Mar 10, 2015 12:35 pm
Country: WALES
Suzuki 2-Strokes: suzuki gt 550j
Location: Wales

Re: Part supplier

Post by GTandcbr »

Hi i can give you a few links
https://www.discountbikespares.co.uk" onclick="window.open(this.href);return false;" onclick="window.open(this.href);return false;
https://www.robinsonsfoundry.co.uk/shop ... finder.htm" onclick="window.open(this.href);return false;" onclick="window.open(this.href);return false;
http://www.suzygtparts.com" onclick="window.open(this.href);return false;" onclick="window.open(this.href);return false;
http://www.francosmotorcycle.com/produc ... /gt-range/" onclick="window.open(this.href);return false;" onclick="window.open(this.href);return false;
Finally if you send an email to gtreiner1@aol.com he will send you a parts list
Good luck
You may want to put some photos of your bike up as a way of introduction :D
Welcome to the forum
98 carb Blackbird and GT550j
Zunspec4
Expert racer
Posts: 1087
Joined: Tue Dec 16, 2008 11:37 am
Country: UK
Suzuki 2-Strokes: T500R, SV1000S, TS125, Seeley T500
Location: Trowbridge UK

Re: Part supplier

Post by Zunspec4 »

Also Crooks Suzuki in Barrow-in-Furness (UK's oldest Suzuki dealer)

Cheers Geoff
Frogy
Still in the Driveway
Posts: 6
Joined: Mon Apr 02, 2018 3:16 am
Country: England
Suzuki 2-Strokes: Suzuki GT550 1976

Re: Part supplier

Post by Frogy »

Thanks for that i will send you e-mail for Parts list

i will send picture of bike before i start restoration i am aiming to have it done by Christmas no doubt you will be hearing from me in future

cheers Frogu
User avatar
Alan H
Moto GP
Posts: 3155
Joined: Thu Feb 16, 2012 11:50 am
Country: England
Suzuki 2-Strokes: 4 x GT550s - J, M, A, B.
Location: The Republic of South Yorkshire

Re: Part supplier

Post by Alan H »

Depends what you need. I've a garage full of GT550 parts, not far away in Barnsley.
What do you intend doing with the bike?
Think of how stupid the average person is, then realise that half of them are more stupid than that.
Frogy
Still in the Driveway
Posts: 6
Joined: Mon Apr 02, 2018 3:16 am
Country: England
Suzuki 2-Strokes: Suzuki GT550 1976

Re: Part supplier

Post by Frogy »

Hi Just basically strip down to bear frame have that shot blasted and powder coated then rebuild replacing damaged or worn parts
the Vapour blast head etc

one thing i would like to do though is put a new wiring loom on as i have done same sort of restoration on two other bikes and alway try and put new loom/harness on but i have been looking and finding it hard to locate a New loom/Harness for the 1976 GT550

regards
sportston
Expert racer
Posts: 1118
Joined: Wed Jul 10, 2013 12:04 pm
Country: England, UK
Suzuki 2-Strokes: FZ50, GP100, RG125 Gamma, GT380, Bandit 1200S

Re: Part supplier

Post by sportston »

Frogy wrote: one thing i would like to do though is put a new wiring loom on as i have done same sort of restoration on two other bikes and alway try and put new loom/harness on but i have been looking and finding it hard to locate a New loom/Harness for the 1976 GT550

regards
you can buy them new genuine parts from Francos. Not cheap, but perhaps a worthwhile investment if you can afford it.
They come in several pieces. This is the front section.
https://www.ebay.co.uk/itm/SUZUKI-GT550 ... SwJwpZ1OTS
However, this will only replace the main wiring loom and not the individual wires from existing old parts that you may be reusing, such as alternator, clocks, switch-gear etc.
On my own restoration I remade all the wiring connections from every component with new terminals soldered on. So even my old bits of wiring have good contact with practically zero resistance. I also replaced regulator and rectifier with solid state and installed an Accent ignition system (very, very easy to do and a worthwhile mod IMHO).
Good luck with your project.
Frogy
Still in the Driveway
Posts: 6
Joined: Mon Apr 02, 2018 3:16 am
Country: England
Suzuki 2-Strokes: Suzuki GT550 1976

Re: Part supplier

Post by Frogy »

Thanks for that i will look at doing same thing


regards
Frogy
Still in the Driveway
Posts: 6
Joined: Mon Apr 02, 2018 3:16 am
Country: England
Suzuki 2-Strokes: Suzuki GT550 1976

Re: Part supplier

Post by Frogy »

Hi just another quick question what type of fork oil would you recommend for my 1976 GT550 i have drained the old oil and just want to be sure


regards
User avatar
Alan H
Moto GP
Posts: 3155
Joined: Thu Feb 16, 2012 11:50 am
Country: England
Suzuki 2-Strokes: 4 x GT550s - J, M, A, B.
Location: The Republic of South Yorkshire

Re: Part supplier

Post by Alan H »

Depends on the ride you want. 20w50 for a more sporty ride, or 10w40 for a softer one.
Use recommended amount for the type of forks you have.
If they're solid or even too stiff, you've put too much in.
Early forks had more oil in, but they all fit the yokes - even 750 forks as they're the same diameter with heavier springs.
Think of how stupid the average person is, then realise that half of them are more stupid than that.
Frogy
Still in the Driveway
Posts: 6
Joined: Mon Apr 02, 2018 3:16 am
Country: England
Suzuki 2-Strokes: Suzuki GT550 1976

Re: Part supplier

Post by Frogy »

Thanks for that i will get that done and move on

one thing i am struggling with is an actual Diagrammed parts list for the actual bike 1976 GT550
the ones that only seem to be around are for GT750 & GT380

are the GT550 rare??????

regards
GTandcbr
Yeah Man, the Interstate
Posts: 590
Joined: Tue Mar 10, 2015 12:35 pm
Country: WALES
Suzuki 2-Strokes: suzuki gt 550j
Location: Wales

Re: Part supplier

Post by GTandcbr »

https://www.partzilla.com/catalog/suzuk ... indy-gt550" onclick="window.open(this.href);return false;
98 carb Blackbird and GT550j
User avatar
Alan H
Moto GP
Posts: 3155
Joined: Thu Feb 16, 2012 11:50 am
Country: England
Suzuki 2-Strokes: 4 x GT550s - J, M, A, B.
Location: The Republic of South Yorkshire

Re: Part supplier

Post by Alan H »

http://www.alpha-sports.com/suzuki_parts.htm" onclick="window.open(this.href);return false;

Pick year, model and part area. They're all on there.
Think of how stupid the average person is, then realise that half of them are more stupid than that.
Post Reply