SUZUKI GT750 LOSS OF POWER
Moderators: oldjapanesebikes, H2RICK, diamondj, Suzsmokeyallan
-
- Still in the Driveway
- Posts: 1
- Joined: Sun Jun 14, 2020 10:04 am
- Country: scotland
- Suzuki 2-Strokes: gt 750 1976
SUZUKI GT750 LOSS OF POWER
my gt750 1976 starts first touch of the button but under acceleration it looses power like a misfire the middle plug is darker than the outer two changed points and condencers
-
- Yeah Man, the Interstate
- Posts: 558
- Joined: Sat Sep 05, 2015 3:14 pm
- Country: us
- Suzuki 2-Strokes: GT
- Location: southeast pa
Re: SUZUKI GT750 LOSS OF POWER
Welcome
Many things can cause issues like this, when you changed points did you set timing?
Are the carbs clean and proper jets with float levels set at the right height?
Are the mufflers open?
Many things can cause issues like this, when you changed points did you set timing?
Are the carbs clean and proper jets with float levels set at the right height?
Are the mufflers open?
76 GT185
77 GT250
77 GT380
76 GT500
73 GT550
73 GT750
74 GT750
71 T250 scrambler
75 T500 cafe
77 GT250
77 GT380
76 GT500
73 GT550
73 GT750
74 GT750
71 T250 scrambler
75 T500 cafe
-
- Expert racer
- Posts: 1254
- Joined: Mon Dec 01, 2008 2:52 am
- Location: Manchester, UK
Re: SUZUKI GT750 LOSS OF POWER
What Karl said above. To add to the bit about the pipes being clear, the triples do tend to get carbon / crud build up in the centre header pipe right where it divides into two to feed each silencer.
Similarly, the outer pipes get a ring of carbon build-up where the header is welded to the body of the silencer, and over time it starts to act like a restrictor washer.
If you have a spare couple of hours, drop the pipes, get an old clutch cable, cut the nipple off one end and fray the strands out so it looked a bit like a small chimney-sweep's brush. Stick the 'brush' end into the pipe and fix the nipple at the other end in the chuck of your electric drill.
Then hold the cable outer, switch the drill on and move the cable in & out so the frayed ends scrape away at the inside of the pipe. A couple of minutes each pipe, then tip all the crap out. You'd be surprised how much carbon comes out. If you don't have an old cable, one of those springy 'drain clearing snakes' from DIY shops is a good substitute.
Similarly, the outer pipes get a ring of carbon build-up where the header is welded to the body of the silencer, and over time it starts to act like a restrictor washer.
If you have a spare couple of hours, drop the pipes, get an old clutch cable, cut the nipple off one end and fray the strands out so it looked a bit like a small chimney-sweep's brush. Stick the 'brush' end into the pipe and fix the nipple at the other end in the chuck of your electric drill.
Then hold the cable outer, switch the drill on and move the cable in & out so the frayed ends scrape away at the inside of the pipe. A couple of minutes each pipe, then tip all the crap out. You'd be surprised how much carbon comes out. If you don't have an old cable, one of those springy 'drain clearing snakes' from DIY shops is a good substitute.
1976 GT380 - wounded by me, and sold on
2006 SV650S - killed by a patch of diesel and a kerb in Feb 2019
2017 SV650 AL7 - naked and unashamed
2006 SV650S - killed by a patch of diesel and a kerb in Feb 2019
2017 SV650 AL7 - naked and unashamed