This malfunction will end your GT750 ride

General discussion about Street two-stroke Suzuki motorcycles.

Moderators: oldjapanesebikes, H2RICK, diamondj, Suzsmokeyallan

Post Reply
User avatar
Evans Ward
To the on ramp
Posts: 326
Joined: Mon Oct 24, 2016 12:35 pm
Country: USA
Suzuki 2-Strokes: 76 GT750, 72 H2 750, 84 RZ350
Location: Macon, GA. USA

This malfunction will end your GT750 ride

Post by Evans Ward »

Had this happen last Sunday while on a ride. Limped it home riding very gingerly. Never saw red on the temp gauge but crept close. I have a new factory plastic gear drive and will replace the pin, washer, and E clip too. Did find a large flat washer that fell out when I removed the starter cover- anyone know where that belongs? It is pictured in the 2nd pic at bottom. I drained gear oil which looked good with no metallic particles. Drained coolant and will flush system again and changing head gasket (NOS factory one). Have the head off and will check it per service manual specs for warpage with a straight edge. Also have a nice spare head just in case. Piston crowns looked good and decarbonized them yesterday too. One other question- is there a large magnet anywhere under the starter cover? I also have the Accent electronic ignition. Thanks for any help!
You do not have the required permissions to view the files attached to this post.
1976 Suzuki GT750 (Maui Blue), 1972 Kawasaki H2 750 Mach IV (Candytone Blue), 1984 Yamaha RZ350 (KRR- Yellow/ Black).
User avatar
Evans Ward
To the on ramp
Posts: 326
Joined: Mon Oct 24, 2016 12:35 pm
Country: USA
Suzuki 2-Strokes: 76 GT750, 72 H2 750, 84 RZ350
Location: Macon, GA. USA

Re: This malfunction will end your GT750 ride

Post by Evans Ward »

A member on the Kettle Club Forum helped me ID it- fits on the starter idler gear shaft.
1976 Suzuki GT750 (Maui Blue), 1972 Kawasaki H2 750 Mach IV (Candytone Blue), 1984 Yamaha RZ350 (KRR- Yellow/ Black).
Craig380
Expert racer
Posts: 1250
Joined: Mon Dec 01, 2008 2:52 am
Location: Manchester, UK

Re: This malfunction will end your GT750 ride

Post by Craig380 »

What a pain in the @ss that it broke up, but you caught it in time and can fix it.

Bloody Japanese crap with built-in obsolescence, only lasting 40+ years :x :wink:
1976 GT380 - wounded by me, and sold on
2006 SV650S - killed by a patch of diesel and a kerb in Feb 2019
2017 SV650 AL7 - naked and unashamed
rngdng
AMA Superbike
Posts: 1769
Joined: Tue Oct 14, 2008 6:47 pm
Location: Blythewood, SC, USA

Re: This malfunction will end your GT750 ride

Post by rngdng »

Evans Ward wrote:Had this happen last Sunday while on a ride. Limped it home riding very gingerly. Never saw red on the temp gauge but crept close. I have a new factory plastic gear drive and will replace the pin, washer, and E clip too. Did find a large flat washer that fell out when I removed the starter cover- anyone know where that belongs? It is pictured in the 2nd pic at bottom. I drained gear oil which looked good with no metallic particles. Drained coolant and will flush system again and changing head gasket (NOS factory one). Have the head off and will check it per service manual specs for warpage with a straight edge. Also have a nice spare head just in case. Piston crowns looked good and decarbonized them yesterday too. One other question- is there a large magnet anywhere under the starter cover? I also have the Accent electronic ignition. Thanks for any help!

I have repaired cracked ones, but not that one!!!
If you stroke it more than twice; you're playing with it.

Too many bikes, too much time, ENOUGH SPACE, FINALLY! Never enough money.........
User avatar
johnakay
I likes them jubblies
Posts: 2365
Joined: Wed Oct 15, 2008 11:19 am
Country: UK
Suzuki 2-Strokes: bike

Re: This malfunction will end your GT750 ride

Post by johnakay »

is there any particular reasons why these are made out of plastic?
why not use brass etc.
If I wanted to make a life-long career out of
working with the mentally retarded I would
have opened a Harley Davidson Dealership
User avatar
Evans Ward
To the on ramp
Posts: 326
Joined: Mon Oct 24, 2016 12:35 pm
Country: USA
Suzuki 2-Strokes: 76 GT750, 72 H2 750, 84 RZ350
Location: Macon, GA. USA

Re: This malfunction will end your GT750 ride

Post by Evans Ward »

johnakay wrote:is there any particular reasons why these are made out of plastic?
why not use brass etc.
I believe it was designed to break before any further extensive damage could be done.
1976 Suzuki GT750 (Maui Blue), 1972 Kawasaki H2 750 Mach IV (Candytone Blue), 1984 Yamaha RZ350 (KRR- Yellow/ Black).
Craig380
Expert racer
Posts: 1250
Joined: Mon Dec 01, 2008 2:52 am
Location: Manchester, UK

Re: This malfunction will end your GT750 ride

Post by Craig380 »

I think Suzuki originally specified nylon / plastic for quieter running compared to a metal gear set: on the 380 triples the gear that drives the contact breaker shaft from the crank is also nylon.

It seems a bit daft when you consider the general racket you get from 2-strokes anyway :wth: :D

When you think about it, it lasted 40+ years, Suzuki never designed the engines to last THAT long
1976 GT380 - wounded by me, and sold on
2006 SV650S - killed by a patch of diesel and a kerb in Feb 2019
2017 SV650 AL7 - naked and unashamed
User avatar
Evans Ward
To the on ramp
Posts: 326
Joined: Mon Oct 24, 2016 12:35 pm
Country: USA
Suzuki 2-Strokes: 76 GT750, 72 H2 750, 84 RZ350
Location: Macon, GA. USA

Re: This malfunction will end your GT750 ride

Post by Evans Ward »

Measured the head for flatness along with the newly acquired one. Both are fully flat with no issues of warpage at all per the 6 different measurement points from factory service manual. This is surprising on the one from the bike based on those temps shown on the gauge and distance back. Suzuki made these things very robust. Hope to have it back together and running by the weekend.
1976 Suzuki GT750 (Maui Blue), 1972 Kawasaki H2 750 Mach IV (Candytone Blue), 1984 Yamaha RZ350 (KRR- Yellow/ Black).
User avatar
Evans Ward
To the on ramp
Posts: 326
Joined: Mon Oct 24, 2016 12:35 pm
Country: USA
Suzuki 2-Strokes: 76 GT750, 72 H2 750, 84 RZ350
Location: Macon, GA. USA

Re: This malfunction will end your GT750 ride

Post by Evans Ward »

Flushed cooling system x 2 and adjusted hose clamps for leakage. Used new thermostat, new OEM head gasket. All back together now! Trying to get this machine road ready and reliable.
1976 Suzuki GT750 (Maui Blue), 1972 Kawasaki H2 750 Mach IV (Candytone Blue), 1984 Yamaha RZ350 (KRR- Yellow/ Black).
Post Reply