GT750 motor in Bimota Frame?
Moderators: oldjapanesebikes, H2RICK, diamondj, Suzsmokeyallan
- RING_DING
- To the on ramp
- Posts: 447
- Joined: Thu Apr 21, 2011 5:32 am
- Country: USA
- Suzuki 2-Strokes: 1974 GT750 B-4 (JDM), 1975 GT750M
- Location: North Carolina
GT750 motor in Bimota Frame?
Calling out to the UK/Irish crew......I grew up in Dublin, Ireland, and I was an avid reader of Bike Magazine (UK) for many years back in the 1970s. I have this strong recollection of reading an article in one issue about a custom bike with a GT750 motor in a Bimota frame. I have searched high & low to try to find this article but no luck. Perhaps I dreamed it up, but I thought I would put it out to see if anyone remembers this?
1973 Suzuki GT750K with Sidecar - Bonneville 2020
- tz375
- Moto GP
- Posts: 6204
- Joined: Mon Nov 03, 2008 10:47 am
- Location: Illinois
Re: GT750 motor in Bimota Frame?
I know there was a one that was dropped into a DRESDA frame. I have no recollection of a BiMoTa
- RING_DING
- To the on ramp
- Posts: 447
- Joined: Thu Apr 21, 2011 5:32 am
- Country: USA
- Suzuki 2-Strokes: 1974 GT750 B-4 (JDM), 1975 GT750M
- Location: North Carolina
Re: GT750 motor in Bimota Frame?
Dim recollections I know, but I think it was a one-off custom project by someone in the UK. It wasn't Bimota themselves.
1973 Suzuki GT750K with Sidecar - Bonneville 2020
- tz375
- Moto GP
- Posts: 6204
- Joined: Mon Nov 03, 2008 10:47 am
- Location: Illinois
Re: GT750 motor in Bimota Frame?
Bike magazine did a series on fitting a GT motor into a Dresda frame. To add to Pedro's comments, there were several articles on S&L bikes including the first one that reportedly was a a Nico Bakker frame though it is very different to every other frame that Nico built.
http://www.thekettleclub.com/bike/isitabakker/" onclick="window.open(this.href);return false;
Does that shed any light on dusty memories?
http://www.thekettleclub.com/bike/isitabakker/" onclick="window.open(this.href);return false;
Does that shed any light on dusty memories?
- RING_DING
- To the on ramp
- Posts: 447
- Joined: Thu Apr 21, 2011 5:32 am
- Country: USA
- Suzuki 2-Strokes: 1974 GT750 B-4 (JDM), 1975 GT750M
- Location: North Carolina
Re: GT750 motor in Bimota Frame?
TZ.....thanks for the post and the link to the Kettle Club articles. Reading those old Bike magazine articles was quite a nostalgia trip! However, I did not have any glimmers of recognition related to the article I had in mind. Maybe I did dream it up after all....wishful thinking!
1973 Suzuki GT750K with Sidecar - Bonneville 2020
- tz375
- Moto GP
- Posts: 6204
- Joined: Mon Nov 03, 2008 10:47 am
- Location: Illinois
Re: GT750 motor in Bimota Frame?
If it wasn't the S&L it must have been the articles in BIKE where they fitted a GT750 motor into a Dresda frame. I have been unable to locate that one on the web so far. I'm sure I have a hard copy (remember them) somewhere.
-
- Around the block
- Posts: 95
- Joined: Thu Dec 05, 2013 12:32 pm
- Country: Austria
- Suzuki 2-Strokes: GT750
Re: GT750 motor in Bimota Frame?
Hello Ring Ding,
I just found this thread now. I am currently building a Bimota HB1 replica with a GT750 engine, just to make your dream come true - when this discussion started on this forum I had no plans to do so. I also found no information that this has been done before. I need to point out that my frame is obviously not an original BIMOTA frame but a very good copy made by a dutch artist. I only had to sacrifice the swingarm pivot location a bit due to the width of the GT engine vs. the CB 750 engine.
See my separate thread " Bimota GT1 replica"
I just found this thread now. I am currently building a Bimota HB1 replica with a GT750 engine, just to make your dream come true - when this discussion started on this forum I had no plans to do so. I also found no information that this has been done before. I need to point out that my frame is obviously not an original BIMOTA frame but a very good copy made by a dutch artist. I only had to sacrifice the swingarm pivot location a bit due to the width of the GT engine vs. the CB 750 engine.
See my separate thread " Bimota GT1 replica"
- RING_DING
- To the on ramp
- Posts: 447
- Joined: Thu Apr 21, 2011 5:32 am
- Country: USA
- Suzuki 2-Strokes: 1974 GT750 B-4 (JDM), 1975 GT750M
- Location: North Carolina
Re: GT750 motor in Bimota Frame?
Thanks Wolfgang! I have subscribed to your HB1 Build thread. Fantastic work:)
1973 Suzuki GT750K with Sidecar - Bonneville 2020